How to Go About boarding up door - https://theflatearth.win/, Up a Door

Protecting investment properties that are vacant from the elements is possible by putting up a door with a board. While it won't stop all destruction, it can help avoid certain problems that come with severe storms.

The idea of boarding up commercial property up doors and windows can deter trespassers, vandals, and squatters. However, it can be expensive and time-consuming to set commercial boarding up service plywood boards over the openings of a property.

Take a measurement of the door

You'll first require a tape measurement. You might also want to keep a ladder or chair handy for when you need to gain a better view at the top of the frame. Wear gloves and protective glasses if you have to make use of these tools.

Once you have the measuring instrument, start by taking the door width measurement. This can be accomplished by running the tape horizontally across the door. Make sure to remove any other door components, such as the door sweep and door sweep, from the measurement. Then, determine the height from the floor to the sill or the lintel. It is important to measure in multiple locations, especially when measuring doors that are older as they might not be an exact rectangular shape. If the measurements are different, use the largest number.

After you've recorded the measurements of height and width then you'll have to figure out what size commercial boarding up service you need for the frame. It should be at a minimum 2 inches wider and 1 inch taller than the door. 2'' higher. This will give you enough space to shim both the frame and frame to fit.

It's a great idea remove the casing or trim around the jambs of the door to be able to see the studs. This will let you take measurements of the exact gap between the frame's studs and the edge.

After you've removed your trim, you'll be able to measure the size of the frame of the door by running the tape measure across the entire frame in three locations and using the smallest measurement as your door's width. Also, you should take measurements of the frame's height from top to bottom on both sides. Choose the shortest measurement to determine the width of your door.

If you're having issues with these measurements, it's a good idea to speak with a professional and have them visit your home to measure for you. They will tell you what size and style of door you'll need and how to prepare your frame to accommodate a replacement door.

Cut the Plywood

A door frame is typically composed of studs or thin boards that create a hollow space around the door. The typical door is held in place by two hinges that are connected to the studs. This means that if you want to finish the door, it's essential te door frame's rails and stiles already drilled and ready to attach the panel to the door frame. It is a fairly straightforward project that does not require a lot of carpentry expertise, so long as you follow the correct procedures and boarding up door use the right tools.

Set boarding up a door a table near the doorway with two sawhorses at each end and framing lumber 2x4s. Lay the full sheet of plywood flat on top the sawhorses using the marks left by the measurement process as a guide to cut. Score the lines with the help of a utility knife, a drywall square or any other metal straight edge. This will serve as a guide to the saw blade, and also prevent splintering of plywood when cutting it.

Put on eye protection and cut along the lines of scoring using a circular or table saw equipped with a fine-tooth blade. Sand the edges of the panels with 120-grit paper to smooth it out and remove any burrs. After sanding the plywood then apply a wood sealer and let it dry according to the manufacturer's instructions.

Install the hinges on the door frame. If you're using a T-hinge, drill holes on the outside edge of your door to allow for the straps of the hinges. Then, put the hinge's outside face on its mark and screw it to the frame with an screw gun. Repeat the process on the inside of the door for all of the hinges remaining, being careful not to overtighten any of them, or the panel may shift.

If you have a single T-hinged outside door, you can make it easier for the latch to close by fishing wire through the loops on the outside hinges. Bend a piece of tie wire in half, and place it through the two holes on the exterior of the door, then connect the wires to tighten them and lock the door.

Install the Plywood

Place the plywood in the opening of the door according to the measurements you took. Shim the frame's header (top) and the sill. Use a level to make sure that there is no slop between the sill and header. If it's not perfect then place another shim if it is needed and continue the process until the sill and the header are even.

After the plywood is in place, fix it with the stainless steel hinge bolts and wingnuts. Make use of a screwgun that has a hex head attachment to avoid stripping off the screws' heads.

While you're at it if your house was built with studs running through the doorway's height make holes for hanger bolts in the plywood and into each framing stud. This is a far easier task than drilling the hole using the drill or drywall saw.

After putting the plywood in place after installation, take measurements of the width and the height of the door opening. If necessary, cut your plywood bottom to be a little higher than the height of your door frame. Cut two pieces of framing wood 1-by-6 as braces for the lower and upper ends. Cut along the lines marked on your plywood with circular blades with teeth that are finely tipped. Wear eye protection. Splinters can be removed from the cuts by using a sanding tool.

After you have the braces set, nail each one to the plywood with pairs of finishing nails 2 inches long. After you're done counter-sink the heads of all the nails. The braces should be sealed with a good wood sealing product, such as the wipe-on polyurethane made by Minwax.

If the door is too large for your doorway, you can put in a piece of decorative molding to fill in the space between the door and jamb or you can resize the opening. However, in most situations, it's more affordable and more convenient to get the right door. It also removes any problems that you might have experienced with the door you originally purchased in the event that it was damaged or was not fit for the opening.