How to Replace a UPVC Door Replacement Lock

If your door lock jams or isn't functioning as it should, you may want to replace it. It may sound complicated but the process is simple and does not require a locksmith professional.

A few basic tools along with a bit of patience, and a lot of care will be enough to get the job done. Here's what you need to do:

Measure the Door

If you're having difficulty locking your uPVC door or it's not closing, then it could be time to get a new lock. If you've just moved into a new home, a tenant moved out without returning keys, or your multipoint gearbox is showing signs of wear and tear, replacing the lock barrel to a new one will provide an additional layer of security.

Before you purchase a new lock, it is necessary to gather some key measurements that will ensure the new lock fits properly and won't affect your home security. The backset is the most important. This is the distance from the middle of the keyhole bore hole to the edge of the door. It's usually 2 3/8 or even 2 3/4 inches. Measure the length with a measuring tape and write down the results.

It is also important to know what the thickness of the faceplate is. This is the size at which the faceplate covers the mechanism of the lock. If you can, buy an alternative lock from the same manufacturer, because they'll be constructed to the same dimensions. If you cannot find the name of the manufacturer or mark on the lock, take a measurement of the width of the cylinder. You can also check this by putting a pencil in the keyhole and measuring from the bottom of the lock up to the centre of the pencil mark on each side of the cylinder.

Once you have the measurements you can begin removing the old cylinder. Start by loosening the screw that holds the handle in place with a Phillips-head screwdriver, then loosen the screws holding the handles' exterior and interior together. Once these screws are removed, you can remove the barrel screw on the exterior handle. Then pull the cylinder out.

If the cylinder becomes stuck in the lock you could try using WD-40, or another fluid. It's important not to push it out with forceful turns can damage the internal gearbox and lead to more problems with the lock. Consider upgrading to a lock with anti-snap and anti-bump security. This will make it more resistant to attacks from thieves.

Source the Lock

If you're replacing upvc door lock and handle a damaged lock following a burglary or upgrading for better security, there are a few things to consider when choosing a new door lock. Make sure you've got the right size cylinder for your door, and ensure you're purchasing from a reputable brand to ensure a good fit and UPVC Door Replacement Lockto ensure that you locate a suitable replacement.

A damaged door lock could be a huge hassle, and it can also pose a serious security risk. It's not uncommon for the locks on uPVC doors to fail and it's crucial to maintain regular maintenance. Experts recommend changing your lock every seven to eight years. If your lock is badly damaged or you're not satisfied with its performance, professional help might be worthwhile.

In the majority of cases, a simple pin-based system known as the euro cylinder is employed to construct uPVC doors. They are easy to use and rarely break down however, they could be vulnerable to attack. Therefore it is recommended to replace your lock's cylinder with an updated model that has anti-snap and anti-bump security to stop burglaries.

The first step to changing your uPVC locks is to remove the handle. This will expose the old cylinder. This can be a little tricky as there are usually some screws hidden underneath the handles, so make sure you have a screwdriver on hand. The next step is to gently tug and wiggle the cylindrical until it is loose. Once it's loose, you can take it out of its socket.

When you have found the right replacement door locks, simply screw it in and reverse the removal process. Be cautious not to over tighten as this can cause the cylinder to get stuck inside the door and stop working as it should. Test the uPVC replacement lock for composite door lock by opening it and closing it both from the inside and outside. It should be able to lock and unlock the door with your key. If not, make sure that the screws are tight and try again.

Install the Lock

Do some research to make sure that the lock you select is right for your door. You'll have to know the backset and UPVC Door Replacement Lock faceplate measurements - that's the distance from the edge of the french door lock replacement to the centre of the cylinder or handle - as well as the lock type to ensure that the new lock is properly fitted without compromising security.

After you've done this, it's time to install the new lock. You should ideally prop the door open, or secure it so that it doesn't shut during the installation process. To begin, use a Phillips-head driver to loosen the screws holding the handle in place. Once they're removed then you'll be able to slide the handle's inner and outer apart.

You can now take out the old cylinder using a screwdriver. it. After removing the cylinder install the replacement lock for composite door lock. Make sure to follow the directions that are specific to your particular model. Once it's in place, you can test the new lock by removing and closing the door from the inside and outside as well as locking and unlocking it from the inside, and then retesting it.

There are many reasons you may need to change the lock on your uPVC doors. It could be that you've recently moved into the property and you don't have a lock key, the previous tenant didn't return it, or you might just prefer an extra secure lock. It should take no more than five minutes to replace the lock's cylinder.

It doesn't matter if your uPVC doors are single-point or multipoint locks, they all share the same basic mechanism. There are some issues that can arise like closing issues or jam. They can be caused by wear and tear, weather conditions or simply due to daily use. The majority of these issues are easily corrected with a little maintenance or by contacting a locksmith.