Automotive key repair shops near me (moved here) Repair - What to Do When Your Car Key Won't Turn in the Ignition

We've all experienced this - the car key won't turn on the ignition. It can happen at the worst possible moment, like when you are loading your trunk with groceries or heading home from work.

Rather than panic, there are several different options to get you back on the road. Here are a few of the most common automotive key repair issues and possible solutions:

Broken or bent keys

The most frequent reason a car owner cannot start their car is a bent key. It can be repaired by simply straightening the key. This may seem simple however, you need to be careful. The key is extremely thin and even bending it small enough could cause it to break.

To accomplish this, you will need an area that is stable, as well as an plier. Grab one end of the key using the pliers, and then bend it back until it is straight. This can be done on a flat surface, or in a vise. After that, you can place it inside the lock to determine whether it turns.

If not, you could require a new one made. You don't need to call a locksmith and your key will work.

It's a good idea keep a spare in your pocket, so that you don't find yourself without a way into your vehicle in the event of a broken key.

If you're experiencing problems with a bent or broken key, you can try applying lubrication on it before trying to insert it into the lock. This will make it easier to move through the cylinder, and prevent it from becoming stuck. You can use a spray graphite powder or lubricant. Make use of the plastic tube that comes with the spray to ensure a more precise application. This will also help prevent moisture from ruining your key fob repairs.

Stuck pins and springs

Sometimes, a pin (also known as a roll pin) or spring could get stuck. Pins are a small piece of metal that measures between 5.1 and 7.6 cm (2.5-3.0 in) long with hollow ends. It is used to connect two parts of an equipment. In most cases you can take a nut off by pulling it out using your fingers or using a wrench.

If you have an older car that is equipped with microchip keys it is likely that the key needs to be programmed in order to work with your car. This process can vary depending on the model of car and the manufacturer.

Call us if you need assistance with your automotive locks or keys! We can repair, replace or programme almost any vehicle key.

Gear Selector

If your car's gear selection gets stuck in park mode, you need to get it checked by a mechanic as soon as you notice it. It's a safety issue and could cause serious damage to your vehicle if you continue to drive it. This could be a sign that the transmission system is experiencing bigger issues, which can be costly to fix.

Luckily, most of the time, this issue can be easily fixed. Most often, the cable end that is connected to the lever c battery cables are working correctly can resolve this problem.

A key repair car fob that is not functioning properly is another common issue with automotive keys. The key fob is connected to your vehicle's computer, and relays signals and commands between the engine and accessory systems. The system could be confused or stop communicating if it is wet or exposed to extreme temperatures.

It is usually possible to reset the lost key fob by following the steps in the owner's guide. Based on the vehicle you have, you may need to open and close the doors, switch lights and Key repair shops near me other electronic devices off and on by pressing a specific sequence of buttons, or shut and open the windows. If this doesn't solve your fob, it may need to be professionally programmed and will require an expert technician. It's worth trying these simple methods before you buy a new fob.

Ignition socket

Modern emergency car key repair keys are equipped with a transponder, which when it is inserted into the ignition, sends out a signal. The signal informs an immobilizer whether the key is in the right place for the car to begin. In the 1990s, car theft was a major issue. The majority of manufacturers have installed this transponder system for safety and insurance reasons.

If you own a brand new vehicle, the only way to replace your keys is at the dealership or directly with the manufacturer. Before you go there make a note of the VIN number of your vehicle (vehicle identification number). This number is usually found on the dashboard, the door jamb or in the owner's manual.

Bring your current working key along to an participating AutoZone store and an associate will utilize machines to trace the contours of your key blank to precisely replicate the original key. The new key will be cut on site by a cutting machine that is precise. If your key is blade style, a key fob, or has a thick black or grey head, it'll need to be programmed to your specific vehicle before it can be used to start the engine.