How to Do a Door Lock Change

The change of your door lock is an easy and inexpensive method to increase the security of your home. The process is not for all. It requires a certain amount of skill and patience.

The cylinder is located within the knob body. The cylinder recognizes the key when it's put into the lock.

Removal of the old lock

First, remove the lock you have been using for a while. It's a fairly simple procedure, but there are a few things to remember. Make sure your new upvc window lock repair cost fits your door. This will ensure it is secure and doesn't leave a gap at the latch or deadbolt.

After removing the latch plate, you will be required to search for two screws or bolts on the inside of the casing that hold the casing together with the two halves of the lock. Unscrew these with the help of a screwdriver, and then pull the lock out of the door. If you have a mortise locking system, there is a set screw that binds the handle to the spindle. Use a screwdriver to unscrew this screw, then remove the doorknobs.

Remove the deadbolt and latch plug from your door jamb. Install the new lock. If you are replacing a mortise lock you should also determine the distance between the lock case and the door's edge to ensure that the new lock will be able to fit.

Many reasons could cause you to change your door lock, for instance believing that someone else has the key or welcoming a new roommate. In any case, you can save money by taking the lock off yourself, rather than hiring an expert to remove it. The process is easier than most people think, and it can be completed in a few minutes.

Begin by taking the handle and trim from your door. Then, you can pry the trim loose with a flat screwdriver. You should be able twist off the majority of it. In certain cases, you may even be able to remove the handles completely. Then, check the handle for a small pinhole on the interior side and insert a straightened clip into it. This will trigger the release mechanism and allow you to remove the handle from the door. Next, examine the interior side of the lock to find a small tab and press it using a flat screwdriver. After the spindle is removed, you are able to remove the housing and cylinder.

Selecting a new lock

You have many options when it comes to choosing the right window lock repairs. Take a look at the various types of locks and choose one that fits the design of your door. Think about the backset, which is the distance between the edge and the middle of lock hole. Also consider the cross bore, which is a small hole at the edge of your door's frame. Choose a lock that fits the door thickness and swing.

Most door locks are graded by BHMA and the American National Standards Institute to give you an idea of how they are able to withstand the rigors of use and how difficult to pick or disable. A lock grade 3 might be the ideal choice for a tranquil apartment complex in a rural area, whereas a lock of grade 1 may be more appropriate case that holds the door, you will have to loosen it.

You can replace the lock cylinder you have used with a new one by sliding it into the case, and then tightening the set screws. Reinstalling the piece that connects the cylinder to an indicator stem for a lock is also crucial. This can be done by pulling three small tabs in the back of the cylindrical using needle-nosed pliers. Then, you can connect the smaller bracket to the back of the cylinder. Then, you need to reinstall the strike plate and latch plate as well as the retaining ring attached to the top lock cylinder.

Installing a new lock

If you're replacing an existing lock, you should start by measuring the width of your door. The majority of residential locksets have a thickness of 3/8 to 1 3/4 inches. If your door is more thick, you will need an extra-thick door kit that includes longer screws as well as an extended tail piece (for door knobs) or spindle extensions (for deadbolts).

Most locks come with a comprehensive installation guide to assist you. Read the instructions carefully prior to beginning the process to make sure that you are following all the steps. The guide will give you a good idea of the amount of skill that is required to complete the task. You may want to ask a person who has experience changing locks for assistance if are changing a lock the first time.

It's a great idea to cover the holes in the old hardware prior to installing the new lock. This will prevent the screws from falling through the holes, and protect any tiles you have put in. It also protects against potential damage from rust grime, dirt and. SECURAM Touch includes the masking strip or gaffer tape, however you can use any tape you own.

After removing the screws that hold the lock's interior to the outside then pull the lock straight away. It is important to do this quickly so that the lock doesn't end up closing itself in a way that could end up damaging the mechanism.

Install the new latch bolt in the upper cross bore of the new lock, if it has one. Make sure that you place it in the right location, which is indicated by an arrow. Then, place the latch plate onto the bolt and secure it in the correct position.

Finally, screw in the deadbolt and strike plate to the door jamb. Test the deadbolt by throwing it few times to ensure that it is extended all the way to the strike plate and is fully secure. If you're using an electronic smart lock, make sure to follow the included instructions for programming it. This involves downloading an application and registering your email address, verifying your identity, and connecting to the wireless network to add your device.