Replacing uPVC Window Handles

The replacement of window handles made of upvc is a simple job. The important thing is to make sure that the replacement handle fits the spindle cut out in the window mechanism.

If you follow the steps below any cockspur handle can fit most windows. The most important factor is the step height of the handle.

What to Look for

As time passes, uPVC handles on many windows in the UK may begin to show signs wear and wear and tear. The handle on the window may become shaky or difficult to operate when this happens. This is a easy task that can be completed by anyone who is familiar with basic hand tools.

The first step is to ensure that the handle is firmly attached to the window frame and in a position that is open. The next step is to find the screws or pins which hold the handle. They are usually on the inside of the handle. They can be removed with the screwdriver and pliers.

Once the handle is loose and sagging, it can be removed from its hinges by gently pulling off. It is then necessary to locate a replacement handle of the same style and size. This can be accomplished online or at a local DIY store, and should take five minutes using an screwdriver.

When replacing the handle on a uPVC handle, it is important to take into consideration the step height. This is the distance between the handle's base and where it is located in the frame of the window. This is a standard measurement and you should check the height of the step prior to ordering an replacement handle.

There are various sizes depending on the type of handle. Inline handles for uPVC windows usually feature lug centers of 31mm There are also handles with cockspur with 43mm centres. Tilt and turn handles are commonly found on windows made of uPVC and they have a special design that allows the window to be slid up to allow for ventilation, and then turned to open the window fully.

The most common cause of breakage in uPVC handles is that they crack internally rather than breaking off from the base section. This makes it difficult to open. It is essential to make sure that any replacement handle is fitted with the same spindle as your original one.

Remove the handle that was previously used

If the handles on your windows are damaged or improperly installed, they could cause double-glazed windows to close and open incorrectly. They could even become stuck. There are many reasons for this including general wear and tear or corrosion of the metal handle. In these instances it is essential to find replacement handles made of upvc as soon as you can to avoid further damage and loss of function.

When replacing the handles of windows made of upvc it is recommended to remove the handles that were previously installed from the window handle repairs. Begin by removing the screw with the handle when it is in a closed position. This will reveal a screw, and once it is removed, you can begin to remove the handle itself. It is a good idea to employ an electric screwdriver to accomplish this since it will make the task easiucial to measure the current handle prior to purchasing a replacement. This will ensure that the handle will fit the window in a proper manner and will be of the correct size. All handles are calibrated in accordance with industry standards, making it easy to determine the right size.

To determine the size of the handle move the window to the open position. You will then be able to see the size of the screw or pin that is holding it. Then take a tape measure or ruler to determine the length of the spindle. Once you know the length of your spindle it is possible to buy a replacement of exactly the same size.

The step height of a upvc window handle is also important to consider when purchasing replacements. The step height is measured from the base to the point where the handle is positioned on the frame. In general, this is approximately 21mm for uPVC windows or 9mm for aluminium. Dropping something in the space will allow you to see how far the handle extends before it meets an obstruction.

Cockspur handles typically have different backset heights based on the style of window they are installed in. Inline Espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles have different backsets depending on the window they are in. This is because they have a spur that extends from their handle and is locked onto a cockspur wedge-striking plate.

Install the new handle

If you've decided to replace the handle, ensure that it is aligned with the screw holes in the external door handles euro lock and secure it using the supplied screws. Install the latch lever in the same way as the main handle if you are also replacing the door handle. Then, attach the door trim once more to conceal the mounting screws.

Tips: To take the head of the metal from the wooden wedge make sure the handle is held so that its wider end is resting on the floor. Use an hammer to tap the thin end of the handle. Be careful not to damage the handle or the spindle.