UPVC Window Repairs

Upvc windows are energy efficient and help reduce heating costs. As they age, however, problems can occur that need to be addressed. This can include faulty handles, hinges or locks.

Wooden window repair is fairly easy for DIY enthusiasts to do themselves. It's cheaper than purchasing a new window repairman near me.

Cracks

Cracks and tears in uPVC windows can be a serious issue. Leaving them unrepaired can lead to water ingress and less effective protection against cold weather and even the potential for structural damage. Find a local builder who is skilled in the repair a window of uPVC frames. They must have the necessary skills and experience as well as the right equipment to get the most effective results. This will ensure that your crack is repaired quickly before it gets worse, and you won't have to replace your double glaze window repair unit or glass.

Small cracks in glass can be fixed by using a variety of DIY solutions. Super glue and masking tape are among the most popular products that can keep cracked glass in place for a few minutes. For deeper cracks, tape may need be extended on both sides.

You can also make use of two-part epoxy to fix broken or cracked glasses. Hardware stores typically sell this product for about $10. Make sure your workspace is prepared prior to mixing the epoxy. Make sure you have the correct equipment for the job, such as a soldering iron.

If your lower or upper sash is difficult to raise, it's likely because the cords on the sash's weights have been damaged. Thankfully, this is a simple repair that can be done using an extension ladder and a flat-head screwdriver. A drip cap that is rotten can be easily replaced at home. The drip caps that are not rot-free are available at most home centers and can be nailed and caulked in place with ease. If you have a double glazing repairs or triple-pane window, be sure to check that one of the panes isn't broken. This is because the gasses that fill the space between the panes are responsible for enhancing energy efficiency and should be retained, not escaping.

Water Leaks

If your uPVC windows are leaking, it can damage the interior of your house and cause costly repairs. Water leaks can also weaken the structure of your house and cause mold growth. It is crucial to address any problems caused by leaking windows as soon as possible to limit damage.

A damaged sealant around window frames is a frequent cause of ndow properly. Begin by laying newspaper or an old blanket on the floor to protect it from any drips or splinters that could be leaking from the window as you work.

Use a white cloth soaked in a mix of detergent and water. This will ensure that you don't leave any color stains on your windows. Note the the hinge channel on your uPVC window when you are ready to start working. Unscrew the channel, and then fill the screw holes inside the frame with epoxy (for uPVC frames) or wood filler. Be sure to smooth the hole before it sets.

Once the holes have been filled, you can put in the hinge channel. Make sure it's centered on the window jamb. Also, make sure that you drill the new holes approximately one quarter inch away from the original locations.

Next, measure the length of the spindle protruding from the underside of the handle and then order an alternative online or bring your old one to the hardware store to purchase a new. Finally, back out the setscrew on the shaft of the operator and smooth it out so that the set screw will secure itself to the shaft (photo). Then, your uPVC windows should be closing easily.

Broken Hinges

You will have difficulty opening or closing your uPVC windows if the hinges are broken or aren't working correctly. This could be a security issue and could also hinder your home from being warm or cold. You can easily purchase an entirely new hinge for your uPVC window. It's important that you use the right hinge for your windows.

This is because the hinges have to be the same size to fit inside the window frame. The most commonly used hinges for uPVC windows are standard 18mm or UPVC 15mm window hinges. There are also specialised hinges for wooden frames. Choosing the correct window hinge for your windows can help you avoid the common issues that homeowners have with their windows, for example, not closing properly.

Your window hinges could be slack or stiff for a variety of reasons. One common cause is that the hinges aren't tightened enough. You can check this using a screwdriver to locate the friction screw that is at the end of the hinge and loosen it. Then, you can adjust it by turning it in either direction.

Call Preston Glass Fix if your UPVC window's hinges aren't functioning correctly. We can provide a quick fix. Our technicians will evaluate the condition of the hinges on your windows and advise you on the best solution for your needs. We can replace the window hinges, re-tension them or install new locking mechanisms to ensure that your UPVC windows are secure and safe for the long haul.

The locks are not working properly

UPVC window mechanisms and locks are an important part of security for your home. They make it difficult to open windows without breaking into the home. When a lock fails, it can be a frustrating experience, but it's an easy fix and you do not need to replace the entire window.

Sometimes, the issue is an issue that could have been prevented by regular maintenance. This is why we recommend having your uPVC windows maintained regularly using our yearly maintenance package to help reduce the likelihood of having problems.

Most modern uPVC windows come with espagnolette locks that work by pushing the nose of the handle across a wedge block, then turning the handle to close the lock. They are very efficient in keeping the window locked, but over time they can start to fail if not properly maintained. We recommend using WD-40 for lubrication at least once per year.

If you notice that your uPVC windows aren't opening and shut as easily as they used to or if the lock is not functioning properly, it is likely that there is a problem with the locking gearbox inside the window frame. Accessing this can be tricky as it requires the removing of the seals that surround the frame and the removal of the handle (be careful not to scratch these).

A locksmith who is skilled in UPVC repair will be able to identify the problem quickly, and then replace the malfunctioning locking mechanism with an exact replacement. This is a fast and simple repair that can save you hundreds of dollars by avoiding the need to buy new windows.